How to Fillet a Walleye
Walleye is one of the best-eating freshwater fish there is. The meat is white, mild and flaky, and it has relatively few bones. With a sharp knife and a little practice, you can turn each fish into two clean, boneless fillets in just a few minutes, plus two small cheeks that many anglers say are the best part of the fish.
If you have never filleted a fish before, don’t worry. The process is the same every time, and after a handful of fish it becomes second nature. This guide covers the tools you need and how to choose a fillet knife, how to prepare the fish, and seven clear steps to remove the fillets and skin. It also explains how to deal with the small pin bones, how to remove the cheeks, how to clean up, and how to store, freeze and cook your fillets. Finally, there is a note on transport rules, which matter in many areas.
Safety: a dull knife is more dangerous than a sharp one, because it slips. Always cut away from your body, and keep your fingers clear of the blade.
What you need
- A fillet knife with a flexible blade of 6 to 7 inches. A thin, flexible blade follows the bones closely, which leaves more meat on the fillet.
- A cutting board. A board with a clamp to hold the tail is very helpful, because walleye are slippery.
- A cut-resistant glove for the hand holding the fish.
- Paper towels to dry the fish and your hands.
- A bowl of cold water and a bag or container for the fillets.
- A sharpener or honing rod, so you can touch up the blade during a big cleaning session.
Choosing a fillet knife
- Blade length: 6 to 7 inches suits walleye, perch and most panfish. Larger fish such as pike and lake trout are easier with an 8 to 9 inch blade.
- Flexibility: a flexible blade is best for walleye, because it bends along the backbone and ribs.
- Handle: choose a handle that gives a secure grip when wet and slimy.
- Electric fillet knives: many anglers who clean a lot of fish use an electric knife. It is fast, but it takes practice to avoid wasting meat.
Prepare the fish
- Keep the fish cold until you are ready to clean it. Cold fish are firmer and easier to fillet.
- Rinse off slime and dirt with cold water.
- Dry the fish with a paper towel so it doesn’t slide on the board.
- Set up your work area with everything within reach: knife, board, water, towels and a bag for the fillets.
Fillet the fish in seven steps
- Cut behind the head. Lay the fish on its side with the back facing you. Cut just behind the gill plate and pectoral fin, down to the backbone but not through it. Angle the blade slightly toward the head to save more meat.
- Turn the blade. Rotate the knife so the edge points toward the tail and the blade lies flat against the backbone.
- Cut along the backbone. Use long, smooth strokes toward the tail, keeping the blade pressed lightly against the bones. You will feel the blade pass over the rib bones. Stop just before the tail, so the fillet stays attached by the skin.
- Flip the fillet. Fold the fillet over so it lies skin side down, still attached at the tail.
- Remove the skin. Slide the knife between the meat and the skin at the tail end. Hold the skin firmly against the board and work the blade forward toward the head end, keeping it flat and angled slightly down toward the skin. Let the blade do the work with a gentle side-to-side motion.
- Remove the rib bones. Slip the blade under the thin rib bones at the front of the fillet and slice them away with a thin, shallow cut, removing as little meat as possible.
- Repeat on the other side. Turn the fish over and follow steps 1 to 6 again.
What about the bones?
Unlike pike, walleye don’t have Y-bones. There is sometimes a short line of small pin bones near the front of the fillet, along the center line. You can feel them by running your finger along the fillet. To remove them, make a small V-shaped cut on each side of the line of bones and lift the thin strip out. It only costs a small amount of meat.
Don’t skip the cheeks
Many anglers will tell you the cheeks are the best part of a walleye. There is a small, round piece of tender meat on each side of the head, just below and behind the eye. On larger fish, the cheeks are well worth the extra minute.
- Feel for the soft, round area on the side of the head below the eye.
- Cut around the cheek in a circle with the tip of the knife.
- Lift the meat out, using the tip of the knife to scoop it free.
- Peel or slice off the skin.
Common filleting mistakes
Most beginners make the same few mistakes. Knowing them in advance saves a lot of meat and frustration.
- Using a dull knife. A dull blade tears the meat and slips off the bones. Sharpen your knife before you start, and touch it up with a honing rod every few fish.
- Cutting through the backbone. In the first cut behind the head, stop when you feel the backbone. Cutting through it makes the rest of the fillet harder to remove cleanly.
- Leaving meat on the bones. If the frame still has a lot of meat on it, keep the blade flatter and closer to the backbone on the next fish.
- Cutting through the skin when skinning. Angle the blade very slightly down toward the skin and keep firm pressure on the skin with your other hand.
- Taking too much with the rib bones. Make the cut under the ribs as thin as possible. A flexible blade helps.
- Rushing. Speed comes with practice. At first, slow and careful cuts give better fillets.
Filleting on the ice
Many anglers prefer to clean fish at home, where it is warm and easy to wash up. If you do fillet fish at the lake, choose a sheltered spot, use a board, and keep the fillets cold but not frozen. Fish that freeze before you fillet them are much harder to clean. Remember to check the transport rules described below before you fillet anything away from home.
Clean up
- Rinse the fillets briefly in cold water to remove any scales or blood.
- Pat them dry with paper towels.
- Dispose of the remains properly. Some areas have rules about where fish waste can be left. Never leave it on the ice or at a public access.
- Wash your board and knife with hot, soapy water, and dry the knife before storing it.
Store and freeze the fillets
- Refrigerate fillets in a sealed container and eat them within one or two days.
- Freeze fillets you won’t eat soon. Vacuum seal them, or place them in a freezer bag covered with water and squeeze out the air. Label each bag with the date.
- Thaw frozen fillets in the refrigerator overnight.
Simple ways to cook walleye
- Pan-fried: dust the fillets in seasoned flour and fry them in butter for a few minutes on each side.
- Battered and fried: a light beer batter gives a crisp coating that suits walleye’s mild flavor.
- Baked: place the fillets on a baking sheet with butter, lemon and herbs, and bake until the meat flakes easily.
- Grilled: cook fillets on a piece of foil with butter and seasoning.
Check the transport rules
Some states and provinces have rules about how fillets can be transported. In some areas, for example, you must leave a patch of skin on each fillet so an officer can identify the species, or keep fish whole until you reach your home or a permanent residence. Check your local regulations before filleting fish at the lake.
Frequently asked questions
How long does it take to fillet a walleye?
A beginner may take five to ten minutes per fish. With practice, many anglers can fillet a walleye in a minute or two.
Should I scale walleye before filleting?
Not if you remove the skin, which is the most common method.
Can I eat the skin?
You can, but most anglers remove it, because the skin can have a stronger taste.
Gear for this: knives, pliers.
Posted November 2026.
Related